A bathroom planner, whether it is a free online tool or squared paper and a tape measure, is only as good as the numbers you feed it. Most layout mistakes we see in Kent bathroom refits are not about taste. A toilet that leaves your knees against the door, a basin you cannot stand square to, a socket in the wrong place or an extractor fan too weak to clear the steam: all of these could have been caught at the planning stage.
This page gives you the measurements to plan with, taken from published UK guidance, so whatever bathroom planner you use, the layout it produces will actually work.
Step 1: measure the room properly
Draw the room to scale before you look at a single suite. Measure:
- every wall, at floor level and again at about 1m high, because walls in older houses are rarely square;
- ceiling height, and the height of any sloping ceiling where it starts and ends;
- the door: its width, which way it opens, and the swing it needs;
- windows: width, height, and the height of the sill from the floor;
- the soil stack position and the waste route, which often fix where the toilet can go;
- radiators, boxing, the airing cupboard, and anything you cannot or will not move.
Mark the soil pipe clearly. Moving a toilet a short way along the same wall is usually straightforward. Moving it across the room, or away from a wall with an accessible soil route, can mean lifting floors or adding a macerator, which is the point where a budget refit becomes an expensive one. Our new bathroom cost guide covers how layout changes affect the price.
Step 2: plan clear space around each fitting
Fittings need space in front of them to be usable, not just space for the fitting itself. The best published set of figures in England is in Approved Document M, Volume 1, for the M4(2) “accessible and adaptable” dwelling standard. It only applies by law to certain new homes, but it is a sound benchmark for any bathroom you want to be comfortable to use now and as you get older. Diagram 2.5 gives these minimum clear access zones:
- Basin: a clear zone 700mm wide by 1100mm deep in front of it. The zone can extend under the basin as far as any fixed obstruction such as a vanity unit or pedestal.
- Bath: a clear zone 1100mm long by 700mm wide alongside the bath.
- Toilet: a clear zone 1100mm deep in front of the WC, with the centre line of the toilet 400mm to 500mm from the adjacent wall.
- Radiators and towel rails should be clear of all access zones.
Access zones may overlap, which is what makes small bathrooms work: one patch of open floor can serve the basin, toilet and bath at once. When you lay out your plan, shade these zones in. If the door swings through them, consider an outward opening door, a pocket door or a smaller fitting.
Basin height and spacing
Basin rims are commonly set at around 800mm to 850mm from the floor, and higher for tall households, especially with a countertop basin that sits on a vanity unit. We cover this in detail in how high should a bathroom sink be. Leave elbow room either side of a basin so you can wash without hitting a wall or a shower screen.
Step 3: plan the electrics around the bathroom zones
Bathrooms are a “special location” for electrical work. Approved Document P defines the controlled space around a bath or shower as extending:
- vertically from the finished floor to a height of 2.25m, or to the shower head if it is fixed higher than that; and
- horizontally 0.6m from the edge of the bath or shower tray, or 1.2m from the centre of the shower head where there is no tray.
Installing a new circuit, replacing a consumer unit, and any addition or alteration to circuits within that space is notifiable work. In practice, use a registered electrician who can self-certify, and make sure you receive the certificate.
For planning purposes:
- Mark the 0.6m zone on your plan. Light fittings, fans and shaver points inside or near it need suitable IP ratings, and your electrician will specify them.
- Approved Document P’s own diagram notes that socket outlets should not be located within 3m of a bath tub or shower tray. Shaver supply units made for bathrooms are the usual way to get a plug-in point.
- Decide on electric underfloor heating, a heated mirror or an electric towel rail now, because each needs a supply planned in before the walls are tiled. See bathroom underfloor heating for the options.
Step 4: size the extractor fan
Approved Document F gives the minimum extract rate for a bathroom with an intermittent extract fan as 15 litres per second. If the bathroom has no external wall, the fan should extract at four air changes per hour. When an existing bathroom is refitted, any existing fan should be kept or replaced, and if a fan is replaced using the existing cabling, that does not need to be notified to building control.
Plan the fan position as part of the layout: ideally high up, close to the shower and as far from the door as possible, so replacement air is drawn across the room. Check the duct route to outside, because a long or bent duct reduces a fan’s real extract rate. Our pages on choosing an extractor fan and stopping bathroom condensation go further.
Step 5: choose fittings that fit the plan, not the other way round
Only now should you start choosing products. With your clearances drawn in, you will know the largest bath, basin and storage that will genuinely fit.
- Shower: a walk-in shower needs a tray and screen sized so water stays inside it. See walk-in shower ideas for tray and glass sizes.
- Basin: a short projection basin or a cloakroom basin can rescue a narrow room. Our basin buying guide covers the types.
- Storage: wall-hung units keep the floor visible and make a room feel larger. A tall bathroom cabinet uses height instead of floor space.
- Floor: pick a slip resistant tile and check the subfloor first, as covered in bathroom floor tiles.
Using an online bathroom planner well
Many bathroom retailers and manufacturers offer free 2D and 3D planning tools. They are good for seeing how a room might look, but they tend to show fittings with no space around them and they rarely know where your soil pipe is. Use them as a final check, and:
- enter the room size from your own measurements, not an estimate;
- add the soil stack, window and door swing before placing anything;
- draw in the clear zones from Step 2 as rectangles, so the tool cannot hide a cramped layout;
- print the plan with dimensions and walk it out on the floor with masking tape before ordering.
That last step catches more mistakes than any software. Stand at the taped basin, sit where the toilet will be, and open the door. If it feels tight on the floor, it will feel tighter when the walls are tiled.
Frequently asked questions
What is the best way to plan a bathroom layout?
Measure the room and mark the soil pipe, door swing and window first. Then mark clear space in front of each fitting, using the Approved Document M figures as a guide, before choosing products. Walk the plan out on the floor with tape before you order.
How much space do you need in front of a toilet?
Approved Document M’s accessible and adaptable standard uses a clear zone 1100mm deep in front of the WC, with the toilet’s centre line 400mm to 500mm from the side wall. Many existing bathrooms have less, but this is a comfortable target.
How much space do you need in front of a basin?
The same standard uses a clear zone 700mm wide and 1100mm deep in front of the basin. It may overlap with the zones for the toilet and bath.
Can I put a plug socket in a bathroom?
Approved Document P’s diagram notes that socket outlets should not be within 3m of a bath or shower tray. A bathroom shaver supply unit is the usual answer. Ask a registered electrician about your room.
What size extractor fan does a bathroom need?
Approved Document F sets a minimum of 15 litres per second for an intermittent bathroom extract fan, or four air changes per hour if the room has no external wall.
Do I need building control for a bathroom refit?
A like-for-like refit usually does not, but new circuits or electrical changes near the bath or shower are notifiable, and new drainage or structural changes may need approval. For help planning a bathroom in Kent, talk to Contemporary Structures.
Related guides
- Conservatory Roof Replacement vs Glass Film: Which Fixes a Too-Hot, Too-Cold Conservatory?
- Air Source Heat Pump Cost in 2026 After the £7,500 Grant: What You Actually Pay
- Do You Need Planning Permission for a Rear Extension in Kent? 2026 Permitted Development Rules
- How Much Does a Conservatory Base Cost in the UK? (2026 Price Guide)
- Do You Need a Party Wall Agreement for a Rear Extension? Cost and Rules Explained
- Underfloor Heating vs Radiators for a Home Extension: Cost, Running Bills and Which to Choose
- How Much Does a House Extension Cost in 2026? Full UK Price Breakdown
- Loft Conversion Cost and Types: Dormer, Hip-to-Gable and Velux Explained
- Kent Home Improvement News: June 2026
- House Extensions: The Complete UK Homeowner's Guide
- Single Storey Extension Ideas, Costs and Planning Rules
- Double Storey Extensions: Costs, Designs and What You Can Build
- Side Return Extensions Explained: Cost, Light and Layout
- Kent Home Improvement News: Mid-June 2026
- Garage Conversion Guide: Cost, Building Regs and Best Uses
- Extension vs Moving House: Which Is Better Value in Kent?
- Wraparound vs Rear Extension: Cost and Space Compared
- House Extension Builders in Kent: Costs, Lead Times and How to Choose
- Conservatory Guide: Styles, Costs and How to Choose One
- Kent Home Improvement News: Late June 2026
- How Much Does a Conservatory Cost in 2026? UK Prices by Type
- Conservatory vs Orangery vs Extension: Which to Build?
- Conservatory Roof Options: Glass, Polycarbonate and Tiled Compared
- Kent Home Improvement News: Early July 2026
- How to Keep a Conservatory Warm in Winter and Cool in Summer
- Tiled Conservatory Roof Cost and Replacement Process Explained
- Conservatories in Kent: Choosing an Installer, Costs and What to Ask
- Kent Home Improvement News: Mid-July 2026
- Roofing Guide: Repairs, Replacement, Materials and Costs
- New Roof Cost UK 2026: Replacement Prices by Roof Type
- Roof Repair Cost UK 2026: Slipped Tiles and Flashing Prices
- 7 Signs Your Roof Needs Replacing (and What You Can Ignore)
- Flat Roof vs Pitched Roof: Cost, Lifespan and Best Uses
- EPDM vs Felt vs Fibreglass Flat Roofs Compared
- Kent Home Improvement News: Mid-July 2026
- Roof Tile Types Explained: Clay, Concrete and Slate Compared
- Fascias, Soffits and Guttering: When to Replace and What It Costs
- How to Find a Good Roofer: Vetting Checklist for UK Homeowners
- Roofers in Kent: Costs, How to Choose and What to Ask in 2026
- Kitchen Renovation Guide: Planning, Cost and Design in 2026
- How Much Does a New Kitchen Cost in 2026? UK Price Guide
- Kitchen Layout Ideas: Galley, L-Shape, Island and Open Plan
- Worktops Compared: Quartz vs Granite vs Laminate vs Solid Wood
- Fitted vs Bespoke vs Flat-Pack Kitchens: Cost and Quality
- Kitchen Island Ideas, Sizes and Costs: A 2026 UK Guide
- Kent Home Improvement News: Late July 2026
- Open Plan Kitchen Diner: Costs, Layouts and Knock-Through Rules
- How Long Does a Kitchen Fitting Take? Realistic UK Timeline
- Kitchen Fitters in Kent: Costs and How to Choose (2026)
- Bathroom Renovation Guide: Planning, Cost and Layout
- New Bathroom Cost 2026: What You'll Pay in the UK
- Kent Home Improvement: Roofing Costs Rise (Aug 2026)
- Small Bathroom Ideas: Layouts That Feel Bigger
- Wet Room Cost 2026: £2,000 to £9,000 Fitted, by Size
- En Suite Cost and Minimum Size: £4,000 to £10,000 in 2026
- Kent Home News: £9,000 Heat Pump Grant Now Open
- Electric vs Mixer vs Power Shower: What Your Boiler Allows
- Bathroom Underfloor Heating Cost: 16p an Hour to Run
- Window Replacement Cost 2026: £350 to £600 Per uPVC Window
- uPVC vs Aluminium Windows: the 1.4 U-Value Rule
- How Long Does a Bathroom Take to Fit? 5 to 10 Working Days
- Home Improvement News: Solar Up 14%, Heat Pumps Down 17%
- Double vs Triple Glazing: Part L Still Stops at 1.4
- Bathroom Fitters in Kent: What to Ask Before You Pay
- Sash Window Repair or Replace? What Kent Councils Allow
- Bifold vs Sliding Doors: What Building Regs Actually Set
- Composite Door Cost 2026: £550 to £2,350 Fitted
- Window Energy Ratings: Band B Is the Rule, Not C
- Replacement Windows: the 1.4 U-Value and Vent Rules
- Double Glazing Kent: the 1.4 U-Value Every Quote Must Hit
- Heat Pumps in Kent: the £7,500 Grant and the 1.5m³ Rule
- Heat Pump vs Gas Boiler: Break-Even Is a SCOP of 3.0
- Permitted Development Rights: The 8m Rear Extension Rule
- Air Source vs Ground Source Heat Pump: £13k or £26k?
- Kent Home News: Council Merger Paused, Heat Pump Bids Up 81%
- Building Regulations Approval: Kent Fees, 10-Year Rule
- Boiler Upgrade Scheme: £9,000 Grants From 21 July 2026
- New Boiler Cost 2026: £1,800 to £4,500 Fitted
- Do Heat Pumps Work in Old Houses? Yes, With 3 Conditions
- Heat Pump Installers in Kent: 8 Checks Before You Sign
- House Rendering in Kent: When the Wall Must Be Insulated
- What Is TrustMark? The Kent Trade Badges That Count
- Home Improvement Grants in Kent: ECO4 Ends 31 December
- Kent Home News: Heating Oil to Be Regulated, £9,000 Grant
- Conservation Area Planning Rules: The 3m Rear Limit
- How to Apply for Planning Permission in Kent: £548, 8 Weeks
- Best Kitchen Cupboard Paint: Match It to the Door Surface
- Should You Pay Builders a Deposit? How Much, and How
- Porch Planning Permission: The 3m² Rule and When It Fails
- Black Kitchen Ideas: Matt or Gloss, and the Light It Needs
- Navy Kitchen Ideas: Hague Blue vs Stiffkey and What Pairs
- White Kitchen Ideas: Warm or Cool White, and What Pairs
- Sage Green Kitchen: 8 Farrow & Ball Shades and Pairings
- Grey Kitchen Ideas: 9 Farrow & Ball Greys and What Pairs
- Oak Kitchen Ideas: Solid vs Veneer, Oil Care, 4 Colour Pairs
- Galley Kitchen Ideas: The 1.2m Aisle Rule and 5 Layout Fixes
- Kent Home News: Heat Pump VAT Returns to 5% in April 2027
- Farmhouse Kitchen Ideas: Sink, Range and 6 Paint Colours
- U-Shaped Kitchen Ideas: 2.4m Minimum Width and Corner Fixes
- Kitchen Window Ideas: 7 Layouts and the 800mm Glass Rule
- Kitchen Shelves: Heights, Brackets and Plasterboard Loads
- Kent Home News: Plan to Scrap the Gas Standing Charge
- Kitchen Extension Ideas: 7 Layouts and the 3m Planning Rule
- Walk In Bathroom Shower Ideas: Trays, 8mm Glass and Fans
- Bathroom Sink Buying: 6 Basin Types, Tap Holes and Wastes
- Bathroom Floor Tiles: Slip Ratings, Sizes, Subfloor Checks
- Bathroom Cladding: PVC, Acrylic or Laminate Over Tiles?
- Black Bathroom Ideas: 4 Farrow & Ball Blacks and What Pairs
- Bathroom Worktops: 6 Materials, Which Suit Undermount Sinks
- Tall Bathroom Cabinets: Sizes, Fixing and Where They Fit
- Sealant Strip for Bathroom Joints: When It Beats Silicone


