Tall bathroom cabinets turn a narrow strip of wall, often the gap beside a basin or behind the door, into the most useful storage in the room. Most are between 300 and 400mm wide and stand somewhere between about 1,400mm and 1,900mm high, so they take up little floor yet hold towels, spare toiletries and cleaning kit that would otherwise end up on the cistern. Getting one right comes down to four things: measuring the space properly, choosing between floor-standing and wall-hung, picking a carcass that copes with steam, and fixing it securely.
This page walks through each, with the measurements we check on bathroom refits around Kent. For a full redesign rather than a single unit, see how Contemporary Structures plan and fit bathrooms from start to finish.
What sizes tall bathroom cabinets come in
The range is wider than most people expect. Victorian Plumbing, one of the largest UK bathroom retailers, says its tall storage range runs to units up to 1,900mm high, and when we checked its listings the great majority of tall units were 400mm wide or less, with only a handful between 401 and 600mm. That tells you what the market is built around: slim units that slot into gaps.
Typical sizes you will find:
- Width: 300mm and 350mm are the most common, with some 250mm units for very tight spots and a few 400 to 600mm double-door units.
- Height: roughly 1,200 to 1,400mm for wall-hung “half-tall” units, and 1,600 to 1,900mm for full tallboys.
- Depth: usually 240 to 375mm. A 300mm-deep unit holds a folded bath towel; anything much shallower is better for bottles than linen.
Always work from the manufacturer’s own specification sheet rather than a retailer summary, as listings for the same unit sometimes disagree by a few millimetres.
How to measure for a tall bathroom cabinet
Measure the space, then the things that stop a cabinet from fitting even when the numbers look fine.
- Width at three heights. Walls in older Kent houses are rarely plumb, so check the gap at the skirting, at waist height and near the top. Use the smallest figure.
- Door swing. A side-hinged door on a 350mm unit needs about 350mm of clear space in front to open fully. Check it will not hit a basin, radiator, towel rail or the bathroom door. Many units can be hinged left or right; confirm before ordering.
- Ceiling and sloping ceilings. Leave room above a full-height unit to tilt it upright during fitting, or it may jam against the ceiling before it stands vertical.
- Skirting and pipework. A floor-standing unit pushed against the wall sits proud by the thickness of the skirting. Boxed-in pipes and the back of a close-coupled cistern can also steal depth. Our page on how to hide bathroom pipes covers boxing options that leave a flat wall.
- Switches and sockets. Mark any shaver socket, light switch pull cord or extractor fan isolator. A cabinet must not cover them.
Floor-standing or wall-hung
Both work, and the choice usually follows the rest of the bathroom furniture.
Floor-standing tallboys are simpler to fit, carry more weight and suit a traditional or Shaker-style room. Their weakness is the plinth: on a bathroom floor it sits in splashes and mopping water, and a chipboard base will swell if the edge seal fails. Look for adjustable feet or a sealed plinth, and run a bead of silicone along the base edge only if the maker recommends it.
Wall-hung units leave the floor clear, which makes a small bathroom look bigger and is easier to clean. They suit modern rooms with a wall-hung vanity and toilet. The trade-off is fixing: a loaded tall cabinet puts a lot of leverage on its top brackets, so the wall behind matters. We cover the wider pros and cons in wall-mounted vs freestanding vanity units.
Fixing a tall cabinet safely
Every tall cabinet, floor-standing included, should be fixed to the wall. A tallboy loaded with toiletries and full of open doors can tip forward, and children climb shelves.
- Masonry walls: drill and plug with the fixings the maker supplies, or a heavier-duty plug and screw suited to the wall, at every bracket position.
- Plasterboard and stud walls: do not rely on light cavity fixings for a wall-hung tall unit. Fix into the timber studs, use heavy-duty cavity anchors rated for the load, or, best of all during a refit, fit a timber noggin or plywood pattress behind the board before it is tiled.
- Tiled walls: use a tile drill bit, start slowly without hammer action and keep fixings at least the tile maker’s recommended distance from tile edges.
- Before drilling, check for hidden pipes and cables with a detector. Cables are often run vertically above and below switches and sockets.
If you are planning a new bathroom, decide where tall units go before the walls are boarded so the backing can go in once and stay hidden.
Materials that survive a steamy bathroom
A tall cabinet spends its life in warm, damp air, and cheaper carcasses fail at the edges and the base first. What to look for:
- Moisture-resistant board. Moisture-resistant MFC or MDF (often green-cored) copes far better than standard chipboard. Check the specification says moisture resistant, not just “suitable for bathrooms”.
- Sealed edges. Every cut edge, including the underside and the holes for hinges, should be edged or sealed. Exposed board soaks up water like a sponge.
- Solid wood and veneers. Lovely in oak or walnut, but they need a good lacquer and a well ventilated room.
- Metal fittings. Soft-close hinges and handles should be stainless or plated for wet rooms; cheap steel rusts.
The single best thing for any bathroom furniture is moving the steam out. A good extractor running long enough after a shower prevents most swelling and mould behind units. See how to stop condensation in a bathroom.
Lit and mirrored tall cabinets: the zone rules
Some tall cabinets have built-in lights, a shaver socket or a mirrored door with LEDs. These are electrical fittings and their position is governed by the bathroom zones in BS 7671, the wiring regulations. Crosswater’s guide to bathroom electrical zones sets out the basics:
- Zone 0 is inside the bath or shower tray.
- Zone 1 is the space above the bath or shower tray up to 2.25m from the floor, needing at least IP44 and 30mA RCD protection.
- Zone 2 stretches 0.6m outside the edge of the bath or shower and up to 2.25m high, needing at least IP44. Crosswater adds that it is good practice to treat the area within 60cm of any basin tap as Zone 2 as well.
A plain tall cabinet with no electrics can go anywhere it fits, although keeping it out of direct shower spray will make it last much longer. An illuminated one must carry an IP rating suitable for the zone it sits in, and the wiring should be done by a qualified electrician.
Where tall cabinets work best
- Beside the basin: the classic spot, pairing with a vanity unit of matching finish.
- Behind the door: a slim 250 to 300mm unit uses wall that is otherwise dead space, as long as the door still opens fully.
- At the end of a bath: where the bath is shorter than the room, the leftover gap is often exactly cabinet width.
- In an en suite: a single tall unit can replace a vanity entirely in a very small room. Our en suite bathroom page has more layouts.
For smaller rooms, matching the cabinet colour to the walls makes a tall unit read as part of the room rather than a block in it. More ideas are in our small bathroom ideas.
Frequently asked questions
How tall should a tall bathroom cabinet be?
Full tallboys usually stand 1,600 to 1,900mm high, which keeps the top shelf within reach for most adults. Wall-hung “half-tall” units of around 1,200 to 1,400mm suit rooms where you want the floor clear or a sloping ceiling limits height.
How deep is a tall bathroom cabinet?
Most are 240 to 375mm deep. Around 300mm holds folded bath towels; shallower units are better for bottles and toiletries and project less into a narrow room.
Can you put a tall cabinet next to a shower?
A plain cabinet with no electrics can, but keep it out of the direct spray and away from the shower screen opening if possible, or the carcass edges will take a soaking every day. A cabinet with lights must suit the electrical zone it sits in.
Do tall bathroom cabinets need fixing to the wall?
Yes. Even floor-standing tallboys should be anchored to stop them tipping forward when doors are open or children climb them. Wall-hung units need fixings into masonry, studs or a pattress board, not light cavity plugs.
Can a tall cabinet go on a plasterboard wall?
It can, if it is fixed into the timber studs, held with heavy-duty cavity anchors rated for the load, or hung on a noggin or plywood board fitted behind the plasterboard. During a refit, putting backing in before tiling is the most reliable option.
Related guides
- Conservatory Roof Replacement vs Glass Film: Which Fixes a Too-Hot, Too-Cold Conservatory?
- Air Source Heat Pump Cost in 2026 After the £7,500 Grant: What You Actually Pay
- Do You Need Planning Permission for a Rear Extension in Kent? 2026 Permitted Development Rules
- How Much Does a Conservatory Base Cost in the UK? (2026 Price Guide)
- Do You Need a Party Wall Agreement for a Rear Extension? Cost and Rules Explained
- Underfloor Heating vs Radiators for a Home Extension: Cost, Running Bills and Which to Choose
- How Much Does a House Extension Cost in 2026? Full UK Price Breakdown
- Loft Conversion Cost and Types: Dormer, Hip-to-Gable and Velux Explained
- Kent Home Improvement News: June 2026
- House Extensions: The Complete UK Homeowner's Guide
- Single Storey Extension Ideas, Costs and Planning Rules
- Double Storey Extensions: Costs, Designs and What You Can Build
- Side Return Extensions Explained: Cost, Light and Layout
- Kent Home Improvement News: Mid-June 2026
- Garage Conversion Guide: Cost, Building Regs and Best Uses
- Extension vs Moving House: Which Is Better Value in Kent?
- Wraparound vs Rear Extension: Cost and Space Compared
- House Extension Builders in Kent: Costs, Lead Times and How to Choose
- Conservatory Guide: Styles, Costs and How to Choose One
- Kent Home Improvement News: Late June 2026
- How Much Does a Conservatory Cost in 2026? UK Prices by Type
- Conservatory vs Orangery vs Extension: Which to Build?
- Conservatory Roof Options: Glass, Polycarbonate and Tiled Compared
- Kent Home Improvement News: Early July 2026
- How to Keep a Conservatory Warm in Winter and Cool in Summer
- Tiled Conservatory Roof Cost and Replacement Process Explained
- Conservatories in Kent: Choosing an Installer, Costs and What to Ask
- Kent Home Improvement News: Mid-July 2026
- Roofing Guide: Repairs, Replacement, Materials and Costs
- New Roof Cost UK 2026: Replacement Prices by Roof Type
- Roof Repair Cost UK 2026: Slipped Tiles and Flashing Prices
- 7 Signs Your Roof Needs Replacing (and What You Can Ignore)
- Flat Roof vs Pitched Roof: Cost, Lifespan and Best Uses
- EPDM vs Felt vs Fibreglass Flat Roofs Compared
- Kent Home Improvement News: Mid-July 2026
- Roof Tile Types Explained: Clay, Concrete and Slate Compared
- Fascias, Soffits and Guttering: When to Replace and What It Costs
- How to Find a Good Roofer: Vetting Checklist for UK Homeowners
- Roofers in Kent: Costs, How to Choose and What to Ask in 2026
- Kitchen Renovation Guide: Planning, Cost and Design in 2026
- How Much Does a New Kitchen Cost in 2026? UK Price Guide
- Kitchen Layout Ideas: Galley, L-Shape, Island and Open Plan
- Worktops Compared: Quartz vs Granite vs Laminate vs Solid Wood
- Fitted vs Bespoke vs Flat-Pack Kitchens: Cost and Quality
- Kitchen Island Ideas, Sizes and Costs: A 2026 UK Guide
- Kent Home Improvement News: Late July 2026
- Open Plan Kitchen Diner: Costs, Layouts and Knock-Through Rules
- How Long Does a Kitchen Fitting Take? Realistic UK Timeline
- Kitchen Fitters in Kent: Costs and How to Choose (2026)
- Bathroom Renovation Guide: Planning, Cost and Layout
- New Bathroom Cost 2026: What You'll Pay in the UK
- Kent Home Improvement: Roofing Costs Rise (Aug 2026)
- Small Bathroom Ideas: Layouts That Feel Bigger
- Wet Room Cost 2026: £2,000 to £9,000 Fitted, by Size
- En Suite Cost and Minimum Size: £4,000 to £10,000 in 2026
- Kent Home News: £9,000 Heat Pump Grant Now Open
- Electric vs Mixer vs Power Shower: What Your Boiler Allows
- Bathroom Underfloor Heating Cost: 16p an Hour to Run
- Window Replacement Cost 2026: £350 to £600 Per uPVC Window
- uPVC vs Aluminium Windows: the 1.4 U-Value Rule
- How Long Does a Bathroom Take to Fit? 5 to 10 Working Days
- Home Improvement News: Solar Up 14%, Heat Pumps Down 17%
- Double vs Triple Glazing: Part L Still Stops at 1.4
- Bathroom Fitters in Kent: What to Ask Before You Pay
- Sash Window Repair or Replace? What Kent Councils Allow
- Bifold vs Sliding Doors: What Building Regs Actually Set
- Composite Door Cost 2026: £550 to £2,350 Fitted
- Window Energy Ratings: Band B Is the Rule, Not C
- Replacement Windows: the 1.4 U-Value and Vent Rules
- Double Glazing Kent: the 1.4 U-Value Every Quote Must Hit
- Heat Pumps in Kent: the £7,500 Grant and the 1.5m³ Rule
- Heat Pump vs Gas Boiler: Break-Even Is a SCOP of 3.0
- Permitted Development Rights: The 8m Rear Extension Rule
- Air Source vs Ground Source Heat Pump: £13k or £26k?
- Kent Home News: Council Merger Paused, Heat Pump Bids Up 81%
- Building Regulations Approval: Kent Fees, 10-Year Rule
- Boiler Upgrade Scheme: £9,000 Grants From 21 July 2026
- New Boiler Cost 2026: £1,800 to £4,500 Fitted
- Do Heat Pumps Work in Old Houses? Yes, With 3 Conditions
- Heat Pump Installers in Kent: 8 Checks Before You Sign
- House Rendering in Kent: When the Wall Must Be Insulated
- What Is TrustMark? The Kent Trade Badges That Count
- Home Improvement Grants in Kent: ECO4 Ends 31 December
- Kent Home News: Heating Oil to Be Regulated, £9,000 Grant
- Conservation Area Planning Rules: The 3m Rear Limit
- How to Apply for Planning Permission in Kent: £548, 8 Weeks
- Best Kitchen Cupboard Paint: Match It to the Door Surface
- Should You Pay Builders a Deposit? How Much, and How
- Porch Planning Permission: The 3m² Rule and When It Fails
- Black Kitchen Ideas: Matt or Gloss, and the Light It Needs
- Navy Kitchen Ideas: Hague Blue vs Stiffkey and What Pairs
- White Kitchen Ideas: Warm or Cool White, and What Pairs
- Sage Green Kitchen: 8 Farrow & Ball Shades and Pairings
- Grey Kitchen Ideas: 9 Farrow & Ball Greys and What Pairs
- Oak Kitchen Ideas: Solid vs Veneer, Oil Care, 4 Colour Pairs
- Galley Kitchen Ideas: The 1.2m Aisle Rule and 5 Layout Fixes
- Kent Home News: Heat Pump VAT Returns to 5% in April 2027
- Farmhouse Kitchen Ideas: Sink, Range and 6 Paint Colours
- U-Shaped Kitchen Ideas: 2.4m Minimum Width and Corner Fixes
- Kitchen Window Ideas: 7 Layouts and the 800mm Glass Rule
- Kitchen Shelves: Heights, Brackets and Plasterboard Loads
- Kent Home News: Plan to Scrap the Gas Standing Charge
- Kitchen Extension Ideas: 7 Layouts and the 3m Planning Rule
- Walk In Bathroom Shower Ideas: Trays, 8mm Glass and Fans
- Bathroom Sink Buying: 6 Basin Types, Tap Holes and Wastes
- Bathroom Floor Tiles: Slip Ratings, Sizes, Subfloor Checks
- Bathroom Cladding: PVC, Acrylic or Laminate Over Tiles?
- Black Bathroom Ideas: 4 Farrow & Ball Blacks and What Pairs
- Bathroom Worktops: 6 Materials, Which Suit Undermount Sinks


